The standard 72-hour timeline starts after questionnaire submission; confirm the start point for designer-call bookings.

Home › Blog › Plan a Bedroom Around Existing Switchboards and AC Points
All posts
Cost Guide Published Last updated

Plan a Bedroom Around Existing Switchboards and AC Points

Plan your bed, wardrobe and desk around existing switchboards and AC points. Check access, airflow and furniture clearances before installation.

Map existing switchboards and AC provisions before planning bedroom furniture. Test bed, wardrobe and desk positions against reach, airflow and service access, then price any professional alterations before fabrication. Existing points are planning inputs rather than a reason to accept an awkward room.

1. Create a Measured Map of the Existing Points

Photograph every wall straight on and label it: bed wall, window wall, entrance wall or another clear reference.

Record each point’s position from a fixed corner and its height above the finished floor.

For switchboards, measure the whole faceplate—not just its centre. Furniture can overlap an edge even when the centre appears clear.

Existing feature What to record
Switchboard Faceplate dimensions, height, distance from corner and what each switch controls
Power socket Position and intended use; have its suitability checked for the proposed equipment
AC electrical provision Location and installer-confirmed function
AC pipe opening or route Position and any visible routing
AC drain provision Location and installer’s assessment
Indoor AC unit, if installed Model, dimensions and surrounding space
TV or data point Position and proposed equipment
Ceiling fan and lights Locations and control points

A photograph alone cannot confirm circuit capacity, concealed wiring routes or whether an AC provision is ready for use. Have those details checked by the relevant professional.

2. Separate Fixed Constraints from Possible Changes

Some features strongly influence the layout. Others may be adjustable after inspection.

Feature Planning approach
Doors, windows and structural projections Treat as fixed unless a separately assessed alteration is planned
Installed AC and its services Have an AC installer assess any proposed change
Switchboard behind proposed furniture Compare a furniture adjustment with electrician-assessed relocation
Desk charging needs Confirm suitable sockets and cable routing
Decorative wall panelling Design around approved service access
Wardrobe or bedside dimensions Adjust where doing so preserves their usefulness

Avoid assuming that moving a switchboard is either trivial or prohibitively expensive. The work depends on the existing installation, proposed position and required finishing.

Likewise, an AC point marks a provision—not necessarily the best location for every AC model.

3. Position the Bed Before Designing the Headboard

Test the bed’s full external footprint, including the headboard, frame and any storage openings.

Check:

A bedside table that looks compact on a plan may conceal a socket behind its back or place a drawer directly in front of a plug.

Check Reach from the Actual Bed Height

Use a chair or temporary setup to approximate the mattress height and position.

Can the user reach the intended switch without stretching behind the headboard? Is a charger accessible? Will cables fall into a narrow gap?

Consider both occupants if two people use the bed.

Confirm the mattress and bed-frame heights before finalising bedside controls and furniture.

4. Resolve Switchboard Conflicts Before Panelling

Decorative headboards and wall panels should be coordinated with electrical points.

There are three possible routes:

Keep the Point Accessible

Adjust the headboard width, bedside unit or panel arrangement so the switchboard remains usable.

This works when the adjustment does not compromise comfort or create an awkward layout.

Integrate It Through an Approved Detail

Where appropriate, the electrician and joinery installer can coordinate a correctly mounted, accessible point within the finished design.

Do not let the carpenter simply cut an opening and assume that electrical mounting, enclosure and connections are resolved.

Relocate It

If the existing position cannot support the intended use, ask an electrician to assess relocation.

Include wiring, mounting, testing and wall repairs in the quotation. Complete and test the work before closing the area with permanent furniture.

Avoid a shallow access hole that leaves switches difficult to operate or plugs impossible to remove.

5. Plan Around the AC’s Airflow and Maintenance Needs

Furniture must leave the AC’s required air intake, discharge and service areas clear.

Daikin’s installation guidance identifies unobstructed airflow and adequate installation space as important to performance. Its guidance also calls for access for servicing. Exact requirements depend on the model and installation. daikincomfort.com

Ask the AC installer to review the proposed bedroom elevation, including:

Check Comfort at the Bed and Desk

Consider the direction of airflow relative to where people sleep or sit.

For an existing AC, test its normal operation from the proposed positions. For a new unit, ask the installer to explain likely airflow and adjustment options.

A layout should allow comfortable use without placing furniture in the path needed to distribute air around the room.

6. Do Not Build a Wardrobe Around an Unchecked AC Route

A wardrobe or loft can conceal pipes, drains and electrical connections.

Before fabrication, identify what runs behind or above the proposed cabinetry and what access must remain.

Ask:

AC relocation can involve more than moving the indoor unit. Request a complete assessment covering the electrical supply, pipework, drainage, mounting, commissioning and repairs.

7. Fit the Desk and TV to Suitable Service Points

A nearby socket is useful, but it should not be the only reason for choosing a desk location.

Check seating, daylight, screen reflections, chair movement and storage access first. Then have the electrical provision assessed for the actual equipment.

List what will be connected:

For a TV, coordinate the screen, bracket, cabinet and connection points. Confirm that plugs can be accessed and that the selected mount allows the intended installation.

Avoid treating extension leads hidden behind permanent furniture as the default solution to an unresolved layout.

An Illustrative Bedroom Decision

Imagine a bedroom with:

A revised proposal might:

  1. Reduce or reshape the headboard to preserve switch access.
  2. Adjust bedside units around the actual mattress height.
  3. Revise the wardrobe height or position after the AC installer checks required clearances.
  4. Keep the desk near the window if glare and chair access work.
  5. Add or relocate suitable desk points through an electrician where necessary. This is an illustrative planning approach, not a universal solution. The measured room and equipment requirements determine the final arrangement.

What Should Be Included in the Drawings?

Use a floor plan for furniture placement and wall elevations for heights and service coordination.

The final set should identify:

Compare the Cost of Keeping or Moving Points

For each conflict, compare two complete options.

Option Include in the comparison
Adjust furniture Revised dimensions, storage impact, fabrication and finish changes
Move an electrical point Electrician’s work, materials, testing, wall repair and repainting
Relocate the AC Installer-assessed services, mounting, commissioning and related repairs

The cheapest immediate change may not produce the most usable room. Equally, relocating every point for visual symmetry may add work without improving daily use.

Make the decision before furniture production.

Final Checklist Before Fabrication

Frequently asked questions

Should I position my bed according to the existing switches?

Use them as a planning input, alongside circulation, wardrobe access and comfort. Compare a sensible furniture adjustment with professionally assessed electrical changes.

Can a headboard cover a switchboard?

Plan to keep required switches, sockets and service access usable. Resolve conflicts before installing the headboard rather than leaving inaccessible points behind it.

Can I build a loft beside the AC?

Possibly, if the model-specific installation and servicing requirements are maintained. Have the AC installer review the proposed dimensions before fabrication.

Does an existing AC point guarantee the unit can be installed there?

No. The installer needs to assess the mounting location, electrical provision, pipework, drainage and required clearances.

Can my carpenter relocate sockets?

Electrical alterations should be handled by a qualified electrician. The carpenter can coordinate the furniture openings and finishing details.

Can I plan this bedroom online?

Yes, using measured plans, wall photographs and equipment details. Site verification by the execution team remains necessary before electrical work, AC installation or fabrication.

Related guides

Plan your next steps with Houspire

Share wall photographs, measured service positions and appliance information before joinery design. Have relevant trades check proposed changes.

Explore Houspire’s design plans to review your room arrangement before buying or commissioning work. Confirm the selected deliverables and have the execution team verify site dimensions and technical details.